How to get actual A/F value to show on the screen, not lamda

s300 and SManager software questions & answers
Locked
nchatch
Posts: 32
Joined: Fri Nov 25, 2005 4:37 pm

How to get actual A/F value to show on the screen, not lamda

Post by nchatch »

hello all, i was messing with some s300 today and i was trying to get the actual AF to show up instead of lamda voltage, i am using my trusty ole PLX m300 and have it set in the "settings" i checked the AF box but i cant get it to come up on the digital dash set up


any help?


check menu for a few other questions also
nchatch
Posts: 32
Joined: Fri Nov 25, 2005 4:37 pm

Post by nchatch »

so is everyone tuning off lamda voltage??????
jdmspecdc5
Posts: 100
Joined: Tue Jun 07, 2005 3:19 pm

Post by jdmspecdc5 »

have you checked the source? it could be ELD or o2 depending on your setup.
nchatch
Posts: 32
Joined: Fri Nov 25, 2005 4:37 pm

Post by nchatch »

the lamda trace shows up and i can tune fine, no issue at all, i just want to know if there is or IS NOT an option to view it on the main screen or dashboard view while tuning,
cinq
Posts: 25
Joined: Sat Feb 14, 2004 10:15 am
Location: Philadelphia

Re: How to get actual A/F value to show on the screen, not l

Post by cinq »

Good question. I too am interested in having A/F values display on the S300 screen. I'm so use to reading A/F values, and it would be really helpful than the Lamda values to me. :)


Is there an option for that? I've looked.
nchatch
Posts: 32
Joined: Fri Nov 25, 2005 4:37 pm

Re: How to get actual A/F value to show on the screen, not l

Post by nchatch »

cinq wrote:Good question. I too am interested in having A/F values display on the S300 screen. I'm so use to reading A/F values, and it would be really helpful than the Lamda values to me. :)


Is there an option for that? I've looked.

i have looked and looked and i know there has to be a way, i know hondata would not remove such a useful function from the s300, especially since most of us have been tuning s200s for a long while
Jaker
Posts: 139
Joined: Thu Dec 05, 2002 12:37 pm
Location: Vancouver, BC
Contact:

Post by Jaker »

In options, drop down to settings, press the wideband lambda button. There's a lambda unit window. Switch it to "air/fuel ratio".
nchatch
Posts: 32
Joined: Fri Nov 25, 2005 4:37 pm

Post by nchatch »

finally, thank you i will try that and see what i get, thanks again
cinq
Posts: 25
Joined: Sat Feb 14, 2004 10:15 am
Location: Philadelphia

Post by cinq »

Jaker wrote:In options, drop down to settings, press the wideband lambda button. There's a lambda unit window. Switch it to "air/fuel ratio".
Tried that...that don't work.
jdmspecdc5
Posts: 100
Joined: Tue Jun 07, 2005 3:19 pm

Post by jdmspecdc5 »

settings>general>check lamba box
cinq
Posts: 25
Joined: Sat Feb 14, 2004 10:15 am
Location: Philadelphia

Post by cinq »

jdmspecdc5 wrote:settings>general>check lamba box
Did that....but I think I found the answer. I'll check it later on today.

It's under "Options>Sensors"

From there....select "AF" and under "Unit" two choices of Lamda or A/F Ratio.

Hopefully that is the one. :)
Silverbeast
Posts: 127
Joined: Wed May 21, 2003 12:03 am

Post by Silverbeast »

I had to put in the Min and Max values for the A/f vs. the lambda that was auto populated.

Hope this anwsers your question.


I am also attaching a view that i use to tune with, which displays everything you should need.
Attachments
screenshot.jpg
screenshot.jpg (150.34 KiB) Viewed 5492 times
lambdatoaf.JPG
lambdatoaf.JPG (45.08 KiB) Viewed 5494 times
cinq
Posts: 25
Joined: Sat Feb 14, 2004 10:15 am
Location: Philadelphia

Post by cinq »

Silverbeast wrote:I had to put in the Min and Max values for the A/f vs. the lambda that was auto populated.

Hope this anwsers your question.


I am also attaching a view that i use to tune with, which displays everything you should need.

Thanks Silver...for answering our questions. I guess not too many people is up this late! :P
Locked