AEM 30-4110 connection to P28 S300 V3

s300 and SManager software questions & answers
Post Reply
phenx
Posts: 1
Joined: Tue Sep 27, 2016 11:18 am

AEM 30-4110 connection to P28 S300 V3

Post by phenx »

Civic EG with D16z6
P28 ECU with Hondata S300
AEM 30-4110 LSU 4.2 Wideband

The question:
According to the manual, there is 3 wires to use (red, black and white), I do need to use the ECU's battery +12V and ground pins. The white wire, analog 0-5v or 0-1v (there is an 5-stage selector in the back of the gauge). Where do I connect this white wire, and which mode (0-5v lambda, 0-5v afr, 0-1v narrow) to datalog as lambda/afr and use the closed-loop function? Some people say to connect it to the Analog A0 pin, others are saying to connect to the D14 pin. My friend said that connecting it to the D14 could damadge the ECU/Hondata, as he done it with another friend in their car.

Which one is correct?
User avatar
Spunkster
Site Admin
Posts: 22745
Joined: Fri Sep 20, 2002 5:06 pm
Location: Hondata

Re: AEM 30-4110 connection to P28 S300 V3

Post by Spunkster »

Do not use D14 as it is not capable of reading the full voltage range. Use D10 and you can then run in closed loop with the wideband signal.
Jharri1991
Posts: 1
Joined: Mon Aug 08, 2016 6:03 pm

Re: AEM 30-4110 connection to P28 S300 V3

Post by Jharri1991 »

I was wondering the same thing I was told put it on A0
User avatar
Spunkster
Site Admin
Posts: 22745
Joined: Fri Sep 20, 2002 5:06 pm
Location: Hondata

Re: AEM 30-4110 connection to P28 S300 V3

Post by Spunkster »

You cannot run in closed loop that way.
Az786
Posts: 15
Joined: Thu Sep 08, 2016 12:50 pm

Re: AEM 30-4110 connection to P28 S300 V3

Post by Az786 »

Do you have the pin outs for a integra jdm 98 spec as I'm using a s300v3 in a p28 with a conversion harness to work with my obd2a so I can connect the white wire to the eld?
User avatar
Spunkster
Site Admin
Posts: 22745
Joined: Fri Sep 20, 2002 5:06 pm
Location: Hondata

Re: AEM 30-4110 connection to P28 S300 V3

Post by Spunkster »

Ivantintes
Posts: 2
Joined: Wed Nov 22, 2017 5:31 pm

Re: AEM 30-4110 connection to P06 S300 V3

Post by Ivantintes »

I connect the white cable to d10 and close loop but check engine light is on and show eld code
User avatar
Spunkster
Site Admin
Posts: 22745
Joined: Fri Sep 20, 2002 5:06 pm
Location: Hondata

Re: AEM 30-4110 connection to P28 S300 V3

Post by Spunkster »

Please start your own thread and give complete details.
Ivantintes
Posts: 2
Joined: Wed Nov 22, 2017 5:31 pm

Re: AEM 30-4110 connection to P28 S300 V3

Post by Ivantintes »

I connect the wideband cable to d10 and disconec 136,137 and 138 my question I need cut the cable d10 and plug the wideband cable on the ecu d10 cable and configure d10 in close loop and that it's.
Post Reply