Burnout Rev Limit Wiring

s300 and SManager software questions & answers
Post Reply
fabiangt79
Posts: 48
Joined: Sat Nov 01, 2008 10:17 am

Burnout Rev Limit Wiring

Post by fabiangt79 »

Hi,

Can someone advise me how to wire-up from the ecu to the switch for the rev-limit to work?

Which is the recommend switch to use?

I need both the launch control and Rev-limit burn to work, i be using it on a NA car for a drag.

Fabian
fabiangt79
Posts: 48
Joined: Sat Nov 01, 2008 10:17 am

Re: Burnout Rev Limit Wiring

Post by fabiangt79 »

Can i use the A/C switch B5 for wiring?Does anyone have experience in doing that?
portenio78
Posts: 38
Joined: Mon Oct 24, 2011 6:43 am

Re: Burnout Rev Limit Wiring

Post by portenio78 »

it will give you a list of what you can use. One wire will go from the switch to the desired pin you use from those available, then one wire will go from the switch to a ground.
jdm inc
Posts: 22
Joined: Sun Aug 02, 2009 9:43 am

Re: Burnout Rev Limit Wiring

Post by jdm inc »

portenio78 wrote:it will give you a list of what you can use. One wire will go from the switch to the desired pin you use from those available, then one wire will go from the switch to a ground.
x2
T1 Tuned 765@34lbs :) pb 9.75@154 fastest mph 155
http://www.t1racedevelopment.com
http://www.youtube.com/watch?v=lRwE0k9MIl0&feature=plcp
hondatechpr
Posts: 27
Joined: Thu Feb 28, 2008 6:54 am
Location: Guayama P.R.
Contact:

Re: Burnout Rev Limit Wiring

Post by hondatechpr »

if you use for drag only I can imagine that you don't have a/c compressor. So put the launch control to always on and the burn out to a/c switch. when you go to do the burn out turn the a/c on and the when you go to the line turn it off. not any additional wire needed. make sure that when you turn on the a/c that you can see it on on the sensors window to verify that its working
jdm inc
Posts: 22
Joined: Sun Aug 02, 2009 9:43 am

Re: Burnout Rev Limit Wiring

Post by jdm inc »

had a ? when u have the burnout rev limiter on does it take away the anti lag as well? I meaning by when u pull timing and add fuel!
T1 Tuned 765@34lbs :) pb 9.75@154 fastest mph 155
http://www.t1racedevelopment.com
http://www.youtube.com/watch?v=lRwE0k9MIl0&feature=plcp
Lazysk8r2
Posts: 72
Joined: Fri Apr 14, 2006 2:26 pm

Re: Burnout Rev Limit Wiring

Post by Lazysk8r2 »

hondatechpr wrote:if you use for drag only I can imagine that you don't have a/c compressor. So put the launch control to always on and the burn out to a/c switch. when you go to do the burn out turn the a/c on and the when you go to the line turn it off. not any additional wire needed. make sure that when you turn on the a/c that you can see it on on the sensors window to verify that its working
I tried setting a/c for high low boost and was unable. it needs additional wiring. Maybe its different i dunno.
Street Tuner/Dyno Tuner
portenio78
Posts: 38
Joined: Mon Oct 24, 2011 6:43 am

Re: Burnout Rev Limit Wiring

Post by portenio78 »

jdm inc wrote:had a ? when u have the burnout rev limiter on does it take away the anti lag as well? I meaning by when u pull timing and add fuel!
No it will not.
jdm inc
Posts: 22
Joined: Sun Aug 02, 2009 9:43 am

Re: Burnout Rev Limit Wiring

Post by jdm inc »

portenio78 wrote:
jdm inc wrote:had a ? when u have the burnout rev limiter on does it take away the anti lag as well? I meaning by when u pull timing and add fuel!
No it will not.
ok thanks
T1 Tuned 765@34lbs :) pb 9.75@154 fastest mph 155
http://www.t1racedevelopment.com
http://www.youtube.com/watch?v=lRwE0k9MIl0&feature=plcp
hondatechpr
Posts: 27
Joined: Thu Feb 28, 2008 6:54 am
Location: Guayama P.R.
Contact:

Re: Burnout Rev Limit Wiring

Post by hondatechpr »

Lazysk8r2 wrote:
hondatechpr wrote:if you use for drag only I can imagine that you don't have a/c compressor. So put the launch control to always on and the burn out to a/c switch. when you go to do the burn out turn the a/c on and the when you go to the line turn it off. not any additional wire needed. make sure that when you turn on the a/c that you can see it on on the sensors window to verify that its working
I tried setting a/c for high low boost and was unable. it needs additional wiring. Maybe its different i dunno.

did you turn on the blower on? The a/c switch get the signal from the blower switch so both has to be on
Integra 96 B20 Vtec nitrous 115hp 260hp total 12.00ET 115MPH Stock internals hondata S300
monchiy2k
Posts: 10
Joined: Thu Jan 10, 2013 10:50 am

Re: Burnout Rev Limit Wiring

Post by monchiy2k »

Hay guys, can i just run the hand brake wire to the ecu to activate the burnout, i think this is the best way for a lot of reasons....
Steeve_Civic
Posts: 38
Joined: Mon Nov 12, 2012 12:57 am

Re: Burnout Rev Limit Wiring

Post by Steeve_Civic »

What rpm do you setup your brun out rev?
Post Reply