Burnout Rev Limit Wiring
-
- Posts: 48
- Joined: Sat Nov 01, 2008 10:17 am
Burnout Rev Limit Wiring
Hi,
Can someone advise me how to wire-up from the ecu to the switch for the rev-limit to work?
Which is the recommend switch to use?
I need both the launch control and Rev-limit burn to work, i be using it on a NA car for a drag.
Fabian
Can someone advise me how to wire-up from the ecu to the switch for the rev-limit to work?
Which is the recommend switch to use?
I need both the launch control and Rev-limit burn to work, i be using it on a NA car for a drag.
Fabian
-
- Posts: 48
- Joined: Sat Nov 01, 2008 10:17 am
Re: Burnout Rev Limit Wiring
Can i use the A/C switch B5 for wiring?Does anyone have experience in doing that?
-
- Posts: 38
- Joined: Mon Oct 24, 2011 6:43 am
Re: Burnout Rev Limit Wiring
it will give you a list of what you can use. One wire will go from the switch to the desired pin you use from those available, then one wire will go from the switch to a ground.
Re: Burnout Rev Limit Wiring
x2portenio78 wrote:it will give you a list of what you can use. One wire will go from the switch to the desired pin you use from those available, then one wire will go from the switch to a ground.
T1 Tuned 765@34lbs :) pb 9.75@154 fastest mph 155
http://www.t1racedevelopment.com
http://www.youtube.com/watch?v=lRwE0k9MIl0&feature=plcp
http://www.t1racedevelopment.com
http://www.youtube.com/watch?v=lRwE0k9MIl0&feature=plcp
-
- Posts: 27
- Joined: Thu Feb 28, 2008 6:54 am
- Location: Guayama P.R.
- Contact:
Re: Burnout Rev Limit Wiring
if you use for drag only I can imagine that you don't have a/c compressor. So put the launch control to always on and the burn out to a/c switch. when you go to do the burn out turn the a/c on and the when you go to the line turn it off. not any additional wire needed. make sure that when you turn on the a/c that you can see it on on the sensors window to verify that its working
Re: Burnout Rev Limit Wiring
had a ? when u have the burnout rev limiter on does it take away the anti lag as well? I meaning by when u pull timing and add fuel!
T1 Tuned 765@34lbs :) pb 9.75@154 fastest mph 155
http://www.t1racedevelopment.com
http://www.youtube.com/watch?v=lRwE0k9MIl0&feature=plcp
http://www.t1racedevelopment.com
http://www.youtube.com/watch?v=lRwE0k9MIl0&feature=plcp
Re: Burnout Rev Limit Wiring
I tried setting a/c for high low boost and was unable. it needs additional wiring. Maybe its different i dunno.hondatechpr wrote:if you use for drag only I can imagine that you don't have a/c compressor. So put the launch control to always on and the burn out to a/c switch. when you go to do the burn out turn the a/c on and the when you go to the line turn it off. not any additional wire needed. make sure that when you turn on the a/c that you can see it on on the sensors window to verify that its working
Street Tuner/Dyno Tuner
-
- Posts: 38
- Joined: Mon Oct 24, 2011 6:43 am
Re: Burnout Rev Limit Wiring
No it will not.jdm inc wrote:had a ? when u have the burnout rev limiter on does it take away the anti lag as well? I meaning by when u pull timing and add fuel!
Re: Burnout Rev Limit Wiring
ok thanksportenio78 wrote:No it will not.jdm inc wrote:had a ? when u have the burnout rev limiter on does it take away the anti lag as well? I meaning by when u pull timing and add fuel!
T1 Tuned 765@34lbs :) pb 9.75@154 fastest mph 155
http://www.t1racedevelopment.com
http://www.youtube.com/watch?v=lRwE0k9MIl0&feature=plcp
http://www.t1racedevelopment.com
http://www.youtube.com/watch?v=lRwE0k9MIl0&feature=plcp
-
- Posts: 27
- Joined: Thu Feb 28, 2008 6:54 am
- Location: Guayama P.R.
- Contact:
Re: Burnout Rev Limit Wiring
Lazysk8r2 wrote:I tried setting a/c for high low boost and was unable. it needs additional wiring. Maybe its different i dunno.hondatechpr wrote:if you use for drag only I can imagine that you don't have a/c compressor. So put the launch control to always on and the burn out to a/c switch. when you go to do the burn out turn the a/c on and the when you go to the line turn it off. not any additional wire needed. make sure that when you turn on the a/c that you can see it on on the sensors window to verify that its working
did you turn on the blower on? The a/c switch get the signal from the blower switch so both has to be on
Integra 96 B20 Vtec nitrous 115hp 260hp total 12.00ET 115MPH Stock internals hondata S300
Re: Burnout Rev Limit Wiring
Hay guys, can i just run the hand brake wire to the ecu to activate the burnout, i think this is the best way for a lot of reasons....
-
- Posts: 38
- Joined: Mon Nov 12, 2012 12:57 am
Re: Burnout Rev Limit Wiring
What rpm do you setup your brun out rev?