SManager software requests

s300 and SManager software questions & answers
rev hard
Posts: 45
Joined: Tue Nov 16, 2010 5:01 pm

Re: SManager software requests

Post by rev hard » Sun Sep 06, 2015 4:14 pm

Bring back settings for the strain gauge, would be great

Johnny_9
Posts: 312
Joined: Sun Apr 09, 2006 5:12 am

Re: SManager software requests

Post by Johnny_9 » Sat Sep 12, 2015 1:18 am

Change is have a X-Y plot of "rpm" vs "rate of change of rpm"

Muckman
Posts: 11
Joined: Fri Apr 24, 2009 10:02 pm
Location: Rochester, NY
Contact:

Re: SManager software requests

Post by Muckman » Wed Oct 28, 2015 6:37 pm

Closed loop boost control
Integra GSR 13.5:1 GT30R 597hp
Evo9 MR SE

b16bboss
Posts: 9
Joined: Sat Apr 28, 2012 10:20 am

Re: SManager software requests

Post by b16bboss » Wed Nov 04, 2015 12:40 pm

5) Add-on knock module (knock window, frequency, time intergral etc, individual cyl closed loop knock control)

This would be great

coupe-r
Posts: 8
Joined: Wed Mar 04, 2015 8:41 pm

Re: SManager software requests

Post by coupe-r » Sun Nov 08, 2015 2:12 pm

DIRECT SERIAL LOGGING (Innovate products)

That is all......
Other products been doing this for YEARS. Takes out the ground offsets, noise etc. Live tuning is MUCH better and faster sample rate.

S300 V3 you say? Well you can't log the Digital air fuel ratio into the fuel tables for lambda % offset and real time tuning using the digital input Correct?

Or can I using Sensor Overlay Digital input?
I can't use closed loop digital input but that's because the input needs to go through D14 which is fine...

This is all SOOO much easier if you guys just use their serial protocol into SManager....

Luke
Posts: 249
Joined: Thu Mar 26, 2009 10:24 am
Location: Dorsten/Germany

Re: SManager software requests

Post by Luke » Sat Nov 14, 2015 4:19 am

Boost Control via external knob:

Since the S300 has that boost control option it would just be great, if you could setup your maximum boost (in percent of boostcut) via an external knob hooked up to the V3.

if anyhow possible with some feedback in the dash cluster. so setting the boost to 40% of maximum boost the VSS goes to 40 for a moment and then back to the VSS signal from the transmission.

just a thought I had.

kind regards Lukas

Johnny_9
Posts: 312
Joined: Sun Apr 09, 2006 5:12 am

Data Log Export (CSV) - ECTc AITc

Post by Johnny_9 » Wed Dec 16, 2015 1:27 am

Can we get the ECTc and IATc variables exported in the CSV?

I am doing and X-Y-Z plot of A/F,ECT vs ECTc to optimise cold starts and warm-up enrichments

Thanks

User avatar
Hondata
Site Admin
Posts: 8712
Joined: Thu Aug 15, 2002 12:13 pm
Location: Torrance, CA
Contact:

Re: Data Log Export (CSV) - ECTc AITc

Post by Hondata » Wed Dec 16, 2015 10:22 am

Johnny_9 wrote:Can we get the ECTc and IATc variables exported in the CSV?
Done
Hondata

Johnny_9
Posts: 312
Joined: Sun Apr 09, 2006 5:12 am

Re: Data Log Export (CSV) - ECTc AITc

Post by Johnny_9 » Tue Jan 05, 2016 2:30 am

Hondata wrote:
Johnny_9 wrote:Can we get the ECTc and IATc variables exported in the CSV?
Done
Thanks; can you kindly post the Beta!

User avatar
Hondata
Site Admin
Posts: 8712
Joined: Thu Aug 15, 2002 12:13 pm
Location: Torrance, CA
Contact:

Re: SManager software requests

Post by Hondata » Tue Jan 05, 2016 6:08 am

The next release is due in the next couple of days.
Hondata

b16bboss
Posts: 9
Joined: Sat Apr 28, 2012 10:20 am

Re: SManager software requests

Post by b16bboss » Tue Jan 26, 2016 7:31 am

Can we have something in protection that can pull timing when it sees voltage or don't from an input like a knock module

AREA876
Posts: 400
Joined: Tue Jun 15, 2010 6:14 am
Location: Jamaica

Re: SManager software requests

Post by AREA876 » Fri Feb 19, 2016 4:55 am

Still would love to have more adjust ability over target Lambda table than just three points

AREA876
Posts: 400
Joined: Tue Jun 15, 2010 6:14 am
Location: Jamaica

Re: SManager software requests

Post by AREA876 » Fri Feb 19, 2016 5:01 am

Would love to be able to view target Lambda in display and be able to do a graph trace of both target and actual Lambda

skullbasher
Posts: 58
Joined: Sat Oct 29, 2011 1:01 am

Re: SManager software requests

Post by skullbasher » Thu Apr 21, 2016 11:08 pm

Would it be possible to add a feature to the quickspool section that allows you to change the fixed amount of duty cycle (99%) when triggered? This would give us a bit more tunability of the powerband/boost curve. Thanks.

skullbasher
Posts: 58
Joined: Sat Oct 29, 2011 1:01 am

Re: SManager software requests

Post by skullbasher » Thu Apr 21, 2016 11:13 pm

A secondary quickspool table would also be convenient for the high boost table.

Post Reply