k20a2 I/H/E/RBC with IMG CC stage 4 clutch and flywheel
k20a2 I/RH/E/IMG stage 1 clutch and flywheel
What kind of injectors size was the johnnytune done with? What about with RDX 410cc injectors?
-
- Posts: 2
- Joined: Sat Aug 13, 2011 2:18 pm
Re: k20a2 I/H/E/RBC with IMG CC stage 4 clutch and flywheel
I have a similar setup to the original poster. I am currently running the Toda basemap found in Kpro. Car runs pretty good, but also pretty rich at WOT, 11.8-12.3 . How does the map on page 1 compare to the Toda basemap?
I plan to try it out in a few weeks when I get back in town. I lost to a new 2011 5.0 by a couple cars and need more power. :0
I plan to try it out in a few weeks when I get back in town. I lost to a new 2011 5.0 by a couple cars and need more power. :0
-
- Posts: 2
- Joined: Sat Aug 13, 2011 2:18 pm
Re: k20a2 I/H/E/RBC with IMG CC stage 4 clutch and flywheel
What is up with that fuel dip at 5500 RPMs?
Re: k20a2 I/H/E/RBC with IMG CC stage 4 clutch and flywheel
i need some to take a look at this tune and see if they can set it. i installed a set of rdx 410 injectors and im having some cold start problems, it takes several cranks to get it going but after it warms up everything works ok.
mods: k20a3 block, a2 pistons, rods and crank, cc stage 4 clutch kit with light wieght flywheel, k24a2 head with stock cams and skunk2 high comp valves, retianers and springs, rdx 410 injectors, dcrh, costum 3in cai and costum 3in exhoust.
im running the first tune keto posted on this thred so if any one can take a look and let me know.
mods: k20a3 block, a2 pistons, rods and crank, cc stage 4 clutch kit with light wieght flywheel, k24a2 head with stock cams and skunk2 high comp valves, retianers and springs, rdx 410 injectors, dcrh, costum 3in cai and costum 3in exhoust.
im running the first tune keto posted on this thred so if any one can take a look and let me know.
- Attachments
-
- test.kdl
- (7.74 MiB) Downloaded 311 times
Re: k20a2 I/H/E/RBC with IMG CC stage 4 clutch and flywheel
WOW thats a frankenstein setup! Definitely didnt design the kal for that! Get that EP3 to a tuner, PRONTO!
07 Civic Si Sedan (sold)
17 Civic Si Sedan (daily)
02 RSX Type S (project)
Hit me up for free Hondata Help!
17 Civic Si Sedan (daily)
02 RSX Type S (project)
Hit me up for free Hondata Help!
Re: k20a2 I/H/E/RBC with IMG CC stage 4 clutch and flywheel
hey keto i dont know if u still frequent this forum and thread but im going to try out the kal u had on your first post i have a 2002 k20a2 with injen cold air intake, rbc manifold, hondata img, strup shorty header, t1r test pipe no cat, invidia q300 exhaust and some lightweight pullies could you help me with a tune?
Re: k20a2 I/H/E/RBC with IMG CC stage 4 clutch and flywheel
I dont know if YOU still frequent this forum but use the kal from this thread. Avoid race header kals. They wont work with the shorty/test pipe combo. And post a log already!
07 Civic Si Sedan (sold)
17 Civic Si Sedan (daily)
02 RSX Type S (project)
Hit me up for free Hondata Help!
17 Civic Si Sedan (daily)
02 RSX Type S (project)
Hit me up for free Hondata Help!
Re: k20a2 I/H/E/RBC with IMG CC stage 4 clutch and flywheel
Thank you sir!
07 Civic Si Sedan (sold)
17 Civic Si Sedan (daily)
02 RSX Type S (project)
Hit me up for free Hondata Help!
17 Civic Si Sedan (daily)
02 RSX Type S (project)
Hit me up for free Hondata Help!
Re: k20a2 I/H/E/RBC with IMG CC stage 4 clutch and flywheel
I always liked the z1 cams. Swapped them into my a2 when I had it
07 Civic Si Sedan (sold)
17 Civic Si Sedan (daily)
02 RSX Type S (project)
Hit me up for free Hondata Help!
17 Civic Si Sedan (daily)
02 RSX Type S (project)
Hit me up for free Hondata Help!