V4 datalog freezes

K-Series Programmable ECU installation questions / support issues
Post Reply
cabah
Posts: 5
Joined: Tue Dec 01, 2020 3:00 pm

V4 datalog freezes

Post by cabah »

Any one here had similar issues? where the ecu plugs in and laptop says online and normal, and when you try to read sensors to recal the tps and others it freezes to a certain values, and everything i reboot the k manager and do it again, it datalog freezes to the same values again. engine MIL is on and i cant check it either.

HELp

i got some video i will load up
cabah
Posts: 5
Joined: Tue Dec 01, 2020 3:00 pm

Re: V4 datalog freezes

Post by cabah »

183809F1-08E0-4C6C-8B3C-6493E0A8B48A.jpeg
183809F1-08E0-4C6C-8B3C-6493E0A8B48A.jpeg (657.92 KiB) Viewed 1948 times


It always stuck on these
Values whenever datalog, car starts, mil on, and loud and unload maps(i think anyway)
User avatar
Spunkster
Site Admin
Posts: 22737
Joined: Fri Sep 20, 2002 5:06 pm
Location: Hondata

Re: V4 datalog freezes

Post by Spunkster »

What is the serial number that is on the K-Pro board inside the ECU?
cabah
Posts: 5
Joined: Tue Dec 01, 2020 3:00 pm

Re: V4 datalog freezes

Post by cabah »

1A0DF9FA-274D-48CA-BB61-CF435F5FF927.jpeg
1A0DF9FA-274D-48CA-BB61-CF435F5FF927.jpeg (3.54 MiB) Viewed 1947 times
489426B9-23A8-4DDA-9E61-7B0F66DF5366.jpeg
489426B9-23A8-4DDA-9E61-7B0F66DF5366.jpeg (3.8 MiB) Viewed 1947 times

Tried a V1 on the same car, works fine. 🤷‍♂️
User avatar
Spunkster
Site Admin
Posts: 22737
Joined: Fri Sep 20, 2002 5:06 pm
Location: Hondata

Re: V4 datalog freezes

Post by Spunkster »

Who installed the K-Pro into this ECU?
cabah
Posts: 5
Joined: Tue Dec 01, 2020 3:00 pm

Re: V4 datalog freezes

Post by cabah »

This unit here we got it from Speedscience, New Zealand. I been doin some researching, is the PRA ecu have different ecu pin out thats causing this? any input would be great!!

thank you
User avatar
Spunkster
Site Admin
Posts: 22737
Joined: Fri Sep 20, 2002 5:06 pm
Location: Hondata

Re: V4 datalog freezes

Post by Spunkster »

What vehicle is this being used on?

This was sold as an install kit. You may want to have Speedscience take a look at the ECU as well.
cabah
Posts: 5
Joined: Tue Dec 01, 2020 3:00 pm

Re: V4 datalog freezes

Post by cabah »

Hi, this is goin on an S2000 with a K24 swap, 2NRS PNP harness etc. Got it running on the V1 currently to get other small things done. I have contacted Speedscience and it looks like might the ecu it self is the issue. The faulty V4 can upload and start car running, but cant recal or data log anything.

Thank you

regards
Post Reply