PND K-Pro Reverse Lockout HELP!
PND K-Pro Reverse Lockout HELP!
I have been searching for days on how to install the reverse lockout and I have one question. Do I need a relay? So im using 02-04 type s harness with PND Kpro. According to hondata you can activate the reverse lockout with pin B22 (secondary intake runner) by using a PND (type s) calibration. I have moved the wire from B7 RVS to B22 intake runner. So my concern is if it okay to run the car just by moving the wire or do I need to install the relay between them. Please anyone that has done this please let me know asap.
"Changed PRB calibration to activate reverse lock out via pin B22 (secondary intake runner). This allows PND ECUs to be used rather than the PRB ECU."
•https://www.hondata.com/kpro-help
"Changed PRB calibration to activate reverse lock out via pin B22 (secondary intake runner). This allows PND ECUs to be used rather than the PRB ECU."
•https://www.hondata.com/kpro-help
Re: PND K-Pro Reverse Lockout HELP!
You just need to move the wire. No relay is needed.
Re: PND K-Pro Reverse Lockout HELP!
Thank you. I will plug it in now. Do you happen to know when the solenoid gets triggered? Does it get triggered via RPM, Speed, or Load?
Re: PND K-Pro Reverse Lockout HELP!
It is based on speed, exactly as the OEM reverse lockout is.
Re: PND K-Pro Reverse Lockout HELP!
Works like OEM. Confirmed. Thank you so much.
-
- Posts: 1
- Joined: Tue Mar 10, 2020 3:11 pm
Re: PND K-Pro Reverse Lockout HELP!
Hi guys, new to the site. Question, how did you find where pin b22 is? I have to do the same thing.
Re: PND K-Pro Reverse Lockout HELP!
Hello, I just move b7 to b22 on prb calibration with pnd ecu but reverse lockout did not work. Car is jdm dc5 type r, may be I make something incomplete. Am I need to just relocate the wire and thats it?
Thanks.
Re: PND K-Pro Reverse Lockout HELP!
What is the code on the side of the ECU?
Re: PND K-Pro Reverse Lockout HELP!
I don't believe that a PNF-E01 is compatible with K-Pro.
Re: PND K-Pro Reverse Lockout HELP!
Hello, I checked right now and also inside board is PNF-E01 (I did nor open the up cover completely because of there is warranty seal but I just look between cover and writing on the socket section is also PNF-E01). Ecu is come from United Kingdom and kpro works (because I tried it) also wideband works. The only way for reverse lock is I think using the nitrous output?
Re: PND K-Pro Reverse Lockout HELP!
Hello, ecu is PNF-01 from United Kingdom with kpro4 and works. Today I tried to use nitrous output for reverse lock and it did not lock reverse solenoid. So I want to confirm the wirings.
On the relay I wired:
pin e21 to relay 85
relay 86 to switched 12v
relay 30 to rvs solenoid ground
relay 87 to chassis ground
relay 87/2 empty.
Am I make something wrong ?
Re: PND K-Pro Reverse Lockout HELP!
Post a picture of the inside of the ECU?
Re: PND K-Pro Reverse Lockout HELP!
I attached some detailed pictures with kpro and without kpro.
- Attachments
-
- IMG_0615.JPG (4.53 MiB) Viewed 25480 times
-
- IMG_0614.JPG (4.99 MiB) Viewed 25480 times
-
- IMG_0613.JPG (4.58 MiB) Viewed 25480 times
-
- IMG_0612.JPG (4.79 MiB) Viewed 25480 times