KManager V3.2.4 (beta)

K-Series Programmable ECU installation questions / support issues
User avatar
Hondata
Site Admin
Posts: 8686
Joined: Thu Aug 15, 2002 12:13 pm
Location: Torrance, CA
Contact:

KManager V3.2.4 (beta)

Post by Hondata » Thu Oct 18, 2012 10:47 am

This release has improved rev / launch / burnout limiter operation.

V3.2.0 (18 Oct 2012) changes:
  • Improved speed of launch, burnout, shift and overall rev limiters.
  • Fixed datalogging of traction control over slip and retard.
  • Fixed traction control input descriptions.
V3.2.1 (18 Dec 2012) changes:
  • Fixed datalogs not downloading when the datalog memory is full.
V3.2.2 (20 Dec 2012) changes:
  • Fixed PRA calibration load.
V3.2.3 (14 Feb 2013) changes:
  • Reduced after start VTEC & VTC delay from 10 seconds to 1 second.
V3.2.4 (20 Feb 2013)
  • Added the option to use analog inputs for lambda datalogging.
Hondata

Nazul
Posts: 137
Joined: Mon Sep 24, 2012 8:15 am

Re: KManager V3.2.0 (beta)

Post by Nazul » Tue Oct 23, 2012 2:47 am

Dear Hondata,

Whats the procedure to update the ecu of hondata.
Download the mapping in the new version of 3.2.0?
Then save the mapping again and reupload it?

Are these new fixes applied then automatically or how to I need to understand this?

User avatar
Spunkster
Site Admin
Posts: 17764
Joined: Fri Sep 20, 2002 5:06 pm
Location: Hondata
Contact:

Re: KManager V3.2.0 (beta)

Post by Spunkster » Tue Oct 23, 2012 9:48 am

You should already have the calibration saved on your laptop. Then just upload it to the ECU using the new version of software.

Nazul
Posts: 137
Joined: Mon Sep 24, 2012 8:15 am

Re: KManager V3.2.0 (beta)

Post by Nazul » Wed Oct 24, 2012 2:48 am

Ok thanks for the info

05typeR
Posts: 128
Joined: Thu Nov 17, 2011 6:55 pm

Re: KManager V3.2.1 (beta)

Post by 05typeR » Tue Dec 18, 2012 5:52 pm

Hi guys,

I just installed this software V3.2.1 on my PC and now im getting error message when trying to load a calibration file, I also update the laptop and now getting the same problem.

Update: i reinstalled V3.1.6 and everything works again.

User avatar
Spunkster
Site Admin
Posts: 17764
Joined: Fri Sep 20, 2002 5:06 pm
Location: Hondata
Contact:

Re: KManager V3.2.1 (beta)

Post by Spunkster » Wed Dec 19, 2012 10:35 am

What is the error message?

Arno
Posts: 41
Joined: Sun Sep 02, 2012 8:41 am
Location: The Netherlands

Re: KManager V3.2.1 (beta)

Post by Arno » Thu Dec 20, 2012 11:43 am

Same problem here with 3.2.1 on a Windows 7 netbook.

Easy to reproduce.

1> Start Kmanager 3.2.1 (no need to connect to ECU)
2> Button 'New Calibration'
3> Select 'Civic Type R (European) - PRA'
4> Select any of these, eg. k20a2-civictyper-factory.kal
5> Press 'OK'

Error window pops up: 'Could not load C:\Program Files\KManager\Calibrations\k20a2-civictyper-factory.kal'

Same error when opening a pre-existing KAL file.

It WILL, however, select and open a new PRB, PND and PNF calibration.

Perhaps some parsing issue with PRA (or non-PRB) KAL files?

Oh.. And KManager crashes after you try to open a PRA (and it fails) and then you select the 'Tables' button.

Probably because the data wasn't read properly and it's trying to display/process garbage data.

Bye, Arno.

05typeR
Posts: 128
Joined: Thu Nov 17, 2011 6:55 pm

Re: KManager V3.2.1 (beta)

Post by 05typeR » Thu Dec 20, 2012 11:53 am

Thanks arno, that's exactly what's happening.

I'm using a PRA ecu

05typeR
Posts: 128
Joined: Thu Nov 17, 2011 6:55 pm

Re: KManager V3.2.2 (beta)

Post by 05typeR » Wed Dec 26, 2012 4:26 pm

Guys,

I tried the beta 3.2.2 and now im able to load my PRA files but when its connected to the vehicle it give me an error, i think it was something to the tune of kmanager had to close, i have to reinstall 3.1.6 again to regain any communication with my ECU.

Nazul
Posts: 137
Joined: Mon Sep 24, 2012 8:15 am

Re: KManager V3.2.2 (beta)

Post by Nazul » Thu Dec 27, 2012 8:50 am

Version 3.2.0 is working fine for me, i suggest not upgrading it meanwhile for PRA ecus.

05typeR
Posts: 128
Joined: Thu Nov 17, 2011 6:55 pm

Re: KManager V3.2.2 (beta)

Post by 05typeR » Thu Dec 27, 2012 4:56 pm

can Hondata have a section in the downloads where you can select past version of the software?

my last version was 3.2.0 but i can only download 3.1.6

05typeR
Posts: 128
Joined: Thu Nov 17, 2011 6:55 pm

Re: KManager V3.2.2 (beta)

Post by 05typeR » Tue Jan 08, 2013 6:26 pm

are you guys looking into this?

The above question.

User avatar
Hondata
Site Admin
Posts: 8686
Joined: Thu Aug 15, 2002 12:13 pm
Location: Torrance, CA
Contact:

Re: KManager V3.2.2 (beta)

Post by Hondata » Wed Jan 09, 2013 11:37 am

We try to fix problems rather than create them. Why do you need to use an earlier version of the software?
Hondata

fugazzyek
Posts: 35
Joined: Wed Jan 09, 2013 3:45 pm

Re: KManager V3.2.2 (beta)

Post by fugazzyek » Wed Jan 09, 2013 4:01 pm

the new version would fix my problem with the tps?
when i'll try to calibrate the "READ" wont light on

User avatar
Spunkster
Site Admin
Posts: 17764
Joined: Fri Sep 20, 2002 5:06 pm
Location: Hondata
Contact:

Re: KManager V3.2.2 (beta)

Post by Spunkster » Wed Jan 09, 2013 4:19 pm

You need to have your calibration loaded and datalog to be able to calibrate it. Then when you are done you must upload the calibration to the ECU.

Post Reply