Parameters Window>Nitrous/Aux Parameters>Fuel & Ignition
Fuel compensation....Percent instead of value
more easier to tune...
thanks
Search found 116 matches
- Wed Sep 25, 2013 8:24 pm
- Forum: s300 / SManager
- Topic: SManager software requests
- Replies: 336
- Views: 1520591
- Wed Sep 25, 2013 12:58 am
- Forum: s300 / SManager
- Topic: SManager V2.2.7 (beta)
- Replies: 61
- Views: 87389
Re: SManager V2.2.7 (beta)
Parameters Window>Nitrous/Aux Parameters>Fuel & Ignition
Fuel compensation....Percent instead of value
more easier to tune...
thanks
Fuel compensation....Percent instead of value
more easier to tune...
thanks
- Sat Sep 21, 2013 12:03 am
- Forum: s300 / SManager
- Topic: Nitrous/Aux 1 not working
- Replies: 1
- Views: 2071
Nitrous/Aux 1 not working
The Nitrous/Aux 1 is not working but the Nitrous/Aux 2 and 3 is working...
I just found out today when I'm setting it up and testing my water/methanol injection...
I just found out today when I'm setting it up and testing my water/methanol injection...
- Sat Jul 27, 2013 8:29 pm
- Forum: S300 Calibrations
- Topic: base map for supecharger d16z6 block w/y8 head
- Replies: 0
- Views: 2900
base map for supecharger d16z6 block w/y8 head
the motor is a rebuilt (stock spec) but w/wider piston ring gap
- Mon Mar 11, 2013 9:47 am
- Forum: s300 / SManager
- Topic: SManager software requests
- Replies: 336
- Views: 1520591
Re: SManager software requests
X3blackek4 wrote:x2Lyle_57IAL wrote:Need more target lambda values - would be nice to have atleast 5 over the current 3 !
- Tue Mar 05, 2013 8:29 pm
- Forum: s300 / SManager
- Topic: S300 datalog review - hesitation
- Replies: 17
- Views: 8995
Re: S300 datalog review - hesitation
this happened to me today and the other day, the motor sound like missfiring and my wideband showed really rich like it goes to 11:1 afr it only happen between 2k to 3k rpm... i dont have any datalog for now but i will.... this start happening when i updated to 2.2.4 beta vers. new distributor new s...
- Wed Feb 06, 2013 4:25 pm
- Forum: s300 / SManager
- Topic: SManager 2.2.4
- Replies: 46
- Views: 44575
Re: SManager 2.2.4 (beta)
Anybody out there...allm0t0rGSR wrote:i have a problem with boost control, when im in full boost it show 0 or 1% pwm which suppose to be at 50%, it explain more in the datalog... thanks
Everything was working before I updated mine to 2.2.4. Thanks
- Sun Feb 03, 2013 1:08 pm
- Forum: s300 / SManager
- Topic: SManager 2.2.4
- Replies: 46
- Views: 44575
Re: SManager 2.2.4 (beta)
i have a problem with boost control, when im in full boost it show 0 or 1% pwm which suppose to be at 50%, it explain more in the datalog... thanks
- Thu Jan 03, 2013 7:36 pm
- Forum: s300 / SManager
- Topic: SManager 2.2.4
- Replies: 46
- Views: 44575
Re: SManager 2.2.3 (beta)
under the closed loop condition the maximum engine speed can only go upto 5000rpm, i change to 7500rpm but it keep goen back to 5000rpm... thanks same problem here. and I also can't change: under closed loop: - Closed Loop Max TPS (Low) & (High) - I tryed to set max rpm to more than 8000 and it...
- Sun Dec 23, 2012 1:26 am
- Forum: s300 / SManager
- Topic: SManager 2.2.4
- Replies: 46
- Views: 44575
Re: SManager 2.2.3 (beta)
under the closed loop condition the maximum engine speed can only go upto 5000rpm, i change to 7500rpm but it keep goen back to 5000rpm... thanks
- Fri Dec 21, 2012 1:54 am
- Forum: s300 / SManager
- Topic: SManager 2.2.4
- Replies: 46
- Views: 44575
Re: SManager 2.2.2 (beta)
i have a problem on the Minimum TPS for tip in retard. I tried to correct them to 500 rpm and saved calibration, but when I reopen calibration they constantly revert back to 8000 rpm
- Tue Nov 27, 2012 12:41 am
- Forum: s300 / SManager
- Topic: possible map sensor failure?
- Replies: 1
- Views: 1772
Re: possible map sensor failure?
look like you have a defective map sensor or check the wires and connector?
try this one i adjust the fuel compensation
try this one i adjust the fuel compensation
- Sat Oct 20, 2012 12:21 am
- Forum: s300 / SManager
- Topic: SManager software requests
- Replies: 336
- Views: 1520591
Re: SManager software requests
since a lot of data is collected through data logging and some maths is quite fast programmed, it should be possible to insert some kind of "dyno" to the software, which calculates the power depending on acceleration most of the figures needed are included in the software: gear ratio, rev...
- Mon Sep 17, 2012 7:42 pm
- Forum: s300 / SManager
- Topic: Boost Control
- Replies: 1
- Views: 1796
Boost Control
how come the pwm would come on at 1% or 99% instead of 35% at 5 psi? pls help me if anybody out there have experience the samething and fixed it thanks
- Tue Dec 13, 2011 7:10 pm
- Forum: S300 Calibrations
- Topic: D16Y5 TURBO
- Replies: 1
- Views: 2558
D16Y5 TURBO
STOCK MOTOR
Precision Injectors 650CC
PWM MAC SOLENOID
10 PSI
TURBO
.50 Compressor A/R
.63 Turbine A/R
3.0” Inlet / 2.0” Outlet
CAST MANIFOLD
2.5 DOWNPIPE
Precision Injectors 650CC
PWM MAC SOLENOID
10 PSI
TURBO
.50 Compressor A/R
.63 Turbine A/R
3.0” Inlet / 2.0” Outlet
CAST MANIFOLD
2.5 DOWNPIPE