Search found 117 matches

by allm0t0rGSR
Wed Sep 25, 2013 8:24 pm
Forum: s300 / SManager
Topic: SManager software requests
Replies: 308
Views: 109154

Re: SManager software requests

Parameters Window>Nitrous/Aux Parameters>Fuel & Ignition
Fuel compensation....Percent instead of value

more easier to tune...

thanks
by allm0t0rGSR
Wed Sep 25, 2013 12:58 am
Forum: s300 / SManager
Topic: SManager V2.2.7 (beta)
Replies: 61
Views: 35716

Re: SManager V2.2.7 (beta)

Parameters Window>Nitrous/Aux Parameters>Fuel & Ignition
Fuel compensation....Percent instead of value

more easier to tune...

thanks
by allm0t0rGSR
Sat Sep 21, 2013 12:03 am
Forum: s300 / SManager
Topic: Nitrous/Aux 1 not working
Replies: 1
Views: 1193

Nitrous/Aux 1 not working

The Nitrous/Aux 1 is not working but the Nitrous/Aux 2 and 3 is working...
I just found out today when I'm setting it up and testing my water/methanol injection...
by allm0t0rGSR
Sat Jul 27, 2013 8:29 pm
Forum: S300 Calibrations
Topic: base map for supecharger d16z6 block w/y8 head
Replies: 0
Views: 1762

base map for supecharger d16z6 block w/y8 head

the motor is a rebuilt (stock spec) but w/wider piston ring gap
by allm0t0rGSR
Mon Mar 11, 2013 9:47 am
Forum: s300 / SManager
Topic: SManager software requests
Replies: 308
Views: 109154

Re: SManager software requests

blackek4 wrote:
Lyle_57IAL wrote:Need more target lambda values - would be nice to have atleast 5 over the current 3 !
x2
X3
by allm0t0rGSR
Tue Mar 05, 2013 8:29 pm
Forum: s300 / SManager
Topic: S300 datalog review - hesitation
Replies: 17
Views: 5736

Re: S300 datalog review - hesitation

this happened to me today and the other day, the motor sound like missfiring and my wideband showed really rich like it goes to 11:1 afr it only happen between 2k to 3k rpm... i dont have any datalog for now but i will.... this start happening when i updated to 2.2.4 beta vers. new distributor new s...
by allm0t0rGSR
Wed Feb 06, 2013 4:25 pm
Forum: s300 / SManager
Topic: SManager 2.2.4
Replies: 46
Views: 13715

Re: SManager 2.2.4 (beta)

allm0t0rGSR wrote:i have a problem with boost control, when im in full boost it show 0 or 1% pwm which suppose to be at 50%, it explain more in the datalog... thanks
Anybody out there...
Everything was working before I updated mine to 2.2.4. Thanks
by allm0t0rGSR
Sun Feb 03, 2013 1:08 pm
Forum: s300 / SManager
Topic: SManager 2.2.4
Replies: 46
Views: 13715

Re: SManager 2.2.4 (beta)

i have a problem with boost control, when im in full boost it show 0 or 1% pwm which suppose to be at 50%, it explain more in the datalog... thanks
by allm0t0rGSR
Thu Jan 03, 2013 7:36 pm
Forum: s300 / SManager
Topic: SManager 2.2.4
Replies: 46
Views: 13715

Re: SManager 2.2.3 (beta)

under the closed loop condition the maximum engine speed can only go upto 5000rpm, i change to 7500rpm but it keep goen back to 5000rpm... thanks same problem here. and I also can't change: under closed loop: - Closed Loop Max TPS (Low) & (High) - I tryed to set max rpm to more than 8000 and it doe...
by allm0t0rGSR
Sun Dec 23, 2012 1:26 am
Forum: s300 / SManager
Topic: SManager 2.2.4
Replies: 46
Views: 13715

Re: SManager 2.2.3 (beta)

under the closed loop condition the maximum engine speed can only go upto 5000rpm, i change to 7500rpm but it keep goen back to 5000rpm... thanks
by allm0t0rGSR
Fri Dec 21, 2012 1:54 am
Forum: s300 / SManager
Topic: SManager 2.2.4
Replies: 46
Views: 13715

Re: SManager 2.2.2 (beta)

i have a problem on the Minimum TPS for tip in retard. I tried to correct them to 500 rpm and saved calibration, but when I reopen calibration they constantly revert back to 8000 rpm
by allm0t0rGSR
Tue Nov 27, 2012 12:41 am
Forum: s300 / SManager
Topic: possible map sensor failure?
Replies: 1
Views: 1023

Re: possible map sensor failure?

look like you have a defective map sensor or check the wires and connector?

try this one i adjust the fuel compensation
by allm0t0rGSR
Sat Oct 20, 2012 12:21 am
Forum: s300 / SManager
Topic: SManager software requests
Replies: 308
Views: 109154

Re: SManager software requests

since a lot of data is collected through data logging and some maths is quite fast programmed, it should be possible to insert some kind of "dyno" to the software, which calculates the power depending on acceleration most of the figures needed are included in the software: gear ratio, revolutions o...
by allm0t0rGSR
Mon Sep 17, 2012 7:42 pm
Forum: s300 / SManager
Topic: Boost Control
Replies: 1
Views: 974

Boost Control

how come the pwm would come on at 1% or 99% instead of 35% at 5 psi? pls help me if anybody out there have experience the samething and fixed it thanks
by allm0t0rGSR
Tue Dec 13, 2011 7:10 pm
Forum: S300 Calibrations
Topic: D16Y5 TURBO
Replies: 1
Views: 1540

D16Y5 TURBO

STOCK MOTOR
Precision Injectors 650CC
PWM MAC SOLENOID
10 PSI

TURBO
.50 Compressor A/R
.63 Turbine A/R
3.0” Inlet / 2.0” Outlet
CAST MANIFOLD
2.5 DOWNPIPE