Search found 13 matches

by dylans
Fri Sep 25, 2009 5:56 pm
Forum: s300 / SManager
Topic: Why am I running so rich?
Replies: 6
Views: 1750

The "stock" basemap from Hondata for the P74 is way richer than it should be. I ran the Hondata with my B18B completely stock on that basemap and it was running 11:1 AFs. Before the Hondata I got AFs in the 13s on the stock engine. It took me a while of tuning to get that "stock" basemap to not run ...
by dylans
Wed Aug 26, 2009 10:35 am
Forum: s300 / SManager
Topic: Smanager wish list
Replies: 150
Views: 47418

I guess what I was thinking is that the way the FTS feature works is by effectively adding a rev limiter that lowers the revs to what they will be in the next gear. So while that rev limiter is active, the ignition could be retarded and fuel enriched just like with the launch control rev limiter thu...
by dylans
Tue Aug 25, 2009 9:40 pm
Forum: s300 / SManager
Topic: Smanager wish list
Replies: 150
Views: 47418

This may be an odd request but what about adding the anti-lag feature to full throttle shifting?
by dylans
Thu Jul 02, 2009 9:22 am
Forum: s300 / SManager
Topic: newb to tuning
Replies: 3
Views: 1144

I would definitely recommend playing around with the tuning on your car while it is NA.
by dylans
Tue May 19, 2009 12:43 pm
Forum: s300 / SManager
Topic: Engine stuttering and drop in AF
Replies: 7
Views: 2069

You're the boss Spunkster. I will richen up the lower end and post up a new datalog and calibration if it happens again.
by dylans
Mon May 18, 2009 4:46 pm
Forum: s300 / SManager
Topic: Engine stuttering and drop in AF
Replies: 7
Views: 2069

Doesn't that mean it is adding 8% more fuel? It is adding so much fuel because I already leaned out the lower end (below 500 mBar) a ton. That didn't fix it at all. It doesn't seem like it is actually adding too much fuel. There is a huge jump in AF ratio with almost no change in injector pulse widt...
by dylans
Mon May 18, 2009 11:31 am
Forum: s300 / SManager
Topic: Engine stuttering and drop in AF
Replies: 7
Views: 2069

Touche.
by dylans
Sun May 17, 2009 8:12 pm
Forum: s300 / SManager
Topic: Engine stuttering and drop in AF
Replies: 7
Views: 2069

Engine stuttering and drop in AF

Occasionally when I am driving around, especially when the car is hot and I have been driving around for a while, I have an issue where for a few seconds the engine starts stuttering and the AF ratio drop to the minimum on the gauge (10.0). It usually only happens at low MAP, low enough that it shou...
by dylans
Sat Apr 18, 2009 9:52 am
Forum: s300 / SManager
Topic: Exporting Datalog
Replies: 1
Views: 1003

Exporting Datalog

When exporting data to a .csv file, is there anyway that I can choose what data gets exported? Like lets say I wanted gears as well, is there a way I can add that in to be exported? Also, this one is more important, is there a way to get more decimal place in the exported MAP column? It will only ex...
by dylans
Tue Mar 03, 2009 10:25 pm
Forum: s300 / SManager
Topic: Raise in Idle When Datalogging
Replies: 3
Views: 1521

Great! Thank you...any idea on eta for the release of the new version?
by dylans
Tue Mar 03, 2009 5:45 pm
Forum: s300 / SManager
Topic: Raise in Idle When Datalogging
Replies: 3
Views: 1521

Raise in Idle When Datalogging

I have wired in a switch for the on-board datalogging, The switch goes into the B5 Air Conditioning Switch on the ECU. The on-board datalogging works great, my only problem with it is that everytime i flip the switch to on to start datalogging, it raises the idle from around 850rpms to about 1050rpm...
by dylans
Sun Nov 02, 2008 6:49 pm
Forum: s300 / SManager
Topic: S300 B16 Limited at 6000 rpm
Replies: 3
Views: 1226

Make sure you have full throttle shifting disabled.
by dylans
Wed Oct 08, 2008 2:45 pm
Forum: s300 / SManager
Topic: Duty Cycle Conversion
Replies: 4
Views: 2372

Duty Cycle Conversion

I hope this is an easy one. When looking over a datalog file in the Smanager software, the Duty Cycle is displayed. First off, is this is actual duty cycle taken from the ECU or an estimated duty cycle? Second, when I export the datalog into excel, the duty cycle does not carry over as one of column...