Search found 27 matches
- Sun Sep 16, 2012 4:04 am
- Forum: s300 / SManager
- Topic: Smanager 2.1.3 and Traction control
- Replies: 1
- Views: 1345
Smanager 2.1.3 and Traction control
I downloaded the new beta version but i don't get the traction control tab in the parameters windows. I tried downloading again and still doesn't appears. Is there any issue with the software
- Sat Jun 09, 2012 4:26 am
- Forum: Coil Pack Retrofit
- Topic: What Spark Plugs do you use with CPR Kit?
- Replies: 6
- Views: 9388
Re: What Spark Plugs do you use with CPR Kit?
I use BKR8EIX
- Sat Jun 09, 2012 4:19 am
- Forum: S300 Calibrations
- Topic: H22, 25/28 turbo, RC 650cc injectors, stock internals 10psi
- Replies: 2
- Views: 2117
Re: H22, 25/28 turbo, RC 650cc injectors, stock internals 10
The misfire is at idle?
Are You using a wideband or O2 sensor?
What fuel pressure you are using?
What spark plugs you are using?
Are You using a wideband or O2 sensor?
What fuel pressure you are using?
What spark plugs you are using?
- Sat Jun 09, 2012 4:11 am
- Forum: S300 Calibrations
- Topic: JDm B18C LHT JRSC @ 9psi
- Replies: 6
- Views: 4310
Re: JDm B18C LHT JRSC @ 9psi
open the calibration, change the injector size, verify all parameter are compatible with what you have like map sensor and upload.
- Sat Jun 09, 2012 4:05 am
- Forum: S300 Calibrations
- Topic: Stock LS VTEC TURBO MAP. Help!
- Replies: 1
- Views: 1780
- Sat Jun 09, 2012 3:53 am
- Forum: s300 / SManager
- Topic: Burnout Rev Limit Wiring
- Replies: 11
- Views: 6183
Re: Burnout Rev Limit Wiring
if you use for drag only I can imagine that you don't have a/c compressor. So put the launch control to always on and the burn out to a/c switch. when you go to do the burn out turn the a/c on and the when you go to the line turn it off. not any additional wire needed. make sure that when you turn ...
- Tue Jun 05, 2012 6:11 am
- Forum: s300 / SManager
- Topic: Burnout Rev Limit Wiring
- Replies: 11
- Views: 6183
Re: Burnout Rev Limit Wiring
if you use for drag only I can imagine that you don't have a/c compressor. So put the launch control to always on and the burn out to a/c switch. when you go to do the burn out turn the a/c on and the when you go to the line turn it off. not any additional wire needed. make sure that when you turn o...
- Tue Jun 05, 2012 5:58 am
- Forum: s300 / SManager
- Topic: erratic miss after start up
- Replies: 2
- Views: 1395
Re: erratic miss after start up
Verify you idle control valve and fast idle valve
- Sat May 12, 2012 4:29 am
- Forum: s300 / SManager
- Topic: code 22 - VTEC pressure valve
- Replies: 2
- Views: 1587
Re: code 22 - VTEC pressure valve
You probably are loosing oil pressure. Check pressure and bearings
- Wed May 09, 2012 5:18 am
- Forum: s300 / SManager
- Topic: Spark plugs
- Replies: 92
- Views: 151942
Re: Spark plugs
BKR8EIX #8 Stock# 2668
- Thu Apr 05, 2012 4:32 am
- Forum: s300 / SManager
- Topic: VSS drops 10-40 mph during pass..
- Replies: 6
- Views: 1933
Re: VSS drops 10-40 mph during pass..
Check the speed sensor or the plug, sometimes get loose on the pins
- Thu Apr 05, 2012 4:22 am
- Forum: s300 / SManager
- Topic: Lean Start cold engine
- Replies: 5
- Views: 1933
Re: Lean Start cold engine
First check if the coolant sensor is connected and working.
- Thu Apr 05, 2012 4:18 am
- Forum: s300 / SManager
- Topic: always hang when datalog
- Replies: 17
- Views: 6082
Re: always hang when datalog
What Spark Plugs you are using?
- Thu Mar 22, 2012 5:27 am
- Forum: s300 / SManager
- Topic: Spark plugs
- Replies: 92
- Views: 151942
Re: Spark plugs
I hear about E3 spark plugs and I want to know if they are save to use with hondata. Did hondata hade mede some research on them?
- Sun Oct 02, 2011 4:06 am
- Forum: s300 / SManager
- Topic: Water/Meth Injection Problem
- Replies: 14
- Views: 4760
Re: Water/Meth Injection Problem
Move relay pin 85 to switched 12V. As Spunkter said, the computer will provide the ground to activate the relay