Search found 27 matches

by hondatechpr
Sun Sep 16, 2012 4:04 am
Forum: s300 / SManager
Topic: Smanager 2.1.3 and Traction control
Replies: 1
Views: 984

Smanager 2.1.3 and Traction control

I downloaded the new beta version but i don't get the traction control tab in the parameters windows. I tried downloading again and still doesn't appears. Is there any issue with the software
by hondatechpr
Sat Jun 09, 2012 4:19 am
Forum: S300 Calibrations
Topic: H22, 25/28 turbo, RC 650cc injectors, stock internals 10psi
Replies: 2
Views: 1523

Re: H22, 25/28 turbo, RC 650cc injectors, stock internals 10

The misfire is at idle?

Are You using a wideband or O2 sensor?

What fuel pressure you are using?

What spark plugs you are using?
by hondatechpr
Sat Jun 09, 2012 4:11 am
Forum: S300 Calibrations
Topic: JDm B18C LHT JRSC @ 9psi
Replies: 6
Views: 3390

Re: JDm B18C LHT JRSC @ 9psi

open the calibration, change the injector size, verify all parameter are compatible with what you have like map sensor and upload.
by hondatechpr
Sat Jun 09, 2012 3:53 am
Forum: s300 / SManager
Topic: Burnout Rev Limit Wiring
Replies: 11
Views: 3801

Re: Burnout Rev Limit Wiring

if you use for drag only I can imagine that you don't have a/c compressor. So put the launch control to always on and the burn out to a/c switch. when you go to do the burn out turn the a/c on and the when you go to the line turn it off. not any additional wire needed. make sure that when you turn ...
by hondatechpr
Tue Jun 05, 2012 6:11 am
Forum: s300 / SManager
Topic: Burnout Rev Limit Wiring
Replies: 11
Views: 3801

Re: Burnout Rev Limit Wiring

if you use for drag only I can imagine that you don't have a/c compressor. So put the launch control to always on and the burn out to a/c switch. when you go to do the burn out turn the a/c on and the when you go to the line turn it off. not any additional wire needed. make sure that when you turn o...
by hondatechpr
Tue Jun 05, 2012 5:58 am
Forum: s300 / SManager
Topic: erratic miss after start up
Replies: 2
Views: 875

Re: erratic miss after start up

Verify you idle control valve and fast idle valve
by hondatechpr
Sat May 12, 2012 4:29 am
Forum: s300 / SManager
Topic: code 22 - VTEC pressure valve
Replies: 2
Views: 1099

Re: code 22 - VTEC pressure valve

You probably are loosing oil pressure. Check pressure and bearings
by hondatechpr
Wed May 09, 2012 5:18 am
Forum: s300 / SManager
Topic: Spark plugs
Replies: 81
Views: 88847

Re: Spark plugs

BKR8EIX #8 Stock# 2668
by hondatechpr
Thu Apr 05, 2012 4:32 am
Forum: s300 / SManager
Topic: VSS drops 10-40 mph during pass..
Replies: 6
Views: 1277

Re: VSS drops 10-40 mph during pass..

Check the speed sensor or the plug, sometimes get loose on the pins
by hondatechpr
Thu Apr 05, 2012 4:22 am
Forum: s300 / SManager
Topic: Lean Start cold engine
Replies: 5
Views: 1180

Re: Lean Start cold engine

First check if the coolant sensor is connected and working.
by hondatechpr
Thu Apr 05, 2012 4:18 am
Forum: s300 / SManager
Topic: always hang when datalog
Replies: 17
Views: 3666

Re: always hang when datalog

What Spark Plugs you are using?
by hondatechpr
Thu Mar 22, 2012 5:27 am
Forum: s300 / SManager
Topic: Spark plugs
Replies: 81
Views: 88847

Re: Spark plugs

I hear about E3 spark plugs and I want to know if they are save to use with hondata. Did hondata hade mede some research on them?
by hondatechpr
Sun Oct 02, 2011 4:06 am
Forum: s300 / SManager
Topic: Water/Meth Injection Problem
Replies: 14
Views: 3068

Re: Water/Meth Injection Problem

Move relay pin 85 to switched 12V. As Spunkter said, the computer will provide the ground to activate the relay