Search found 25 matches
- Sun Oct 02, 2016 4:48 pm
- Forum: s300 / SManager
- Topic: BBG Settings in Smanager, Boost Control Problems
- Replies: 2
- Views: 8100
Re: BBG Settings in Smanager, Boost Control Problems
Just a little tip here . Pay close attention to the inlet and outlet of the boost solenoid . I was having issues and finally saw the problem . The boost solenoid was backwards .This made boost control very sensitive for me . I was about to give up on the Hondata boost control . Once i fixed this it ...
- Tue Jun 07, 2016 6:07 pm
- Forum: s300 / SManager
- Topic: Boost control issues (searched first!)
- Replies: 5
- Views: 3224
Re: Boost control issues (searched first!)
Wow , i'm having the same problem . My duty cycles are extremely low as i hit 18 psi with 15 percent duty cycle . I did drop my solenoid frequency down from 78hz to 32hz and it made a very small change . I am going to try and lower the frequency again and see what happens . On my car the quick spool...
- Sun Dec 08, 2013 10:45 am
- Forum: s300 / SManager
- Topic: WHEN WILL HONDATA COME OUT WITH GREAT KNOCK CONTROL????
- Replies: 5
- Views: 3124
Re: WHEN WILL HONDATA COME OUT WITH GREAT KNOCK CONTROL????
Don't hold your breath !
- Thu Nov 14, 2013 6:44 pm
- Forum: s300 / SManager
- Topic: SManager V2.2.7 (beta)
- Replies: 61
- Views: 87563
Re: SManager V2.2.7 (beta)
No updates yet ? Wow , its been a while .
- Tue Oct 22, 2013 6:16 pm
- Forum: s300 / SManager
- Topic: When the Fan turns off the ECU disconnects.
- Replies: 17
- Views: 8852
Re: When the Fan turns off the ECU disconnects.
Stock fan swapped in and issue stopped . It only happens with my Spal high cfm unit . I am going to try a capacitor across the fan terminals .
- Tue Sep 10, 2013 7:36 pm
- Forum: s300 / SManager
- Topic: WHEN WILL HONDATA COME OUT WITH GREAT KNOCK CONTROL????
- Replies: 5
- Views: 3124
Re: WHEN WILL HONDATA COME OUT WITH GREAT KNOCK CONTROL????
I have already asked for this . I think the problem is that the architecture of the ecu is old and would be to much trouble to make something work .
- Fri Aug 09, 2013 8:28 pm
- Forum: s300 / SManager
- Topic: When the Fan turns off the ECU disconnects.
- Replies: 17
- Views: 8852
Re: When the Fan turns off the ECU disconnects.
With USB disconnects it is always one of three things: - non resistor spark plugs (check and replace) - laptop chargers than create current loops through the USB cable (run on battery and see if it still occurs) - bad engine / chassis grounds paths The last is the most difficult to track down. Clea...
- Thu Aug 08, 2013 7:45 pm
- Forum: s300 / SManager
- Topic: When the Fan turns off the ECU disconnects.
- Replies: 17
- Views: 8852
Re: When the Fan turns off the ECU disconnects.
Interestingly i have the same problem . I just installed a Spal fan and started having this same issue . When the fan turns on its ok , but as soon as it turns off my laptop freezes . My prior fan never did this . Increased electrical noise must be the issue here . All grounds are clean and in the p...
- Sat Jun 29, 2013 7:48 pm
- Forum: s300 / SManager
- Topic: SManager software requests
- Replies: 336
- Views: 1525460
Re: SManager software requests
A timed ignition retard after launch would be fantastic . This is offered by Msd and works well with the hot rod guys .
- Mon Mar 04, 2013 9:44 am
- Forum: s300 / SManager
- Topic: closed loop headache....
- Replies: 8
- Views: 4833
Re: closed loop headache....
In all honesty i just turn off closed loop . I can never get it to work correctly as it is finicky . All the cars i tune with Hondata i leave in open loop and they all run great with excellent fuel economy . Just tune with a wideband in the car and it will be fine . The a/f ratio will change with dr...
- Sun May 06, 2012 9:50 am
- Forum: s300 / SManager
- Topic: SManager software requests
- Replies: 336
- Views: 1525460
Re: SManager software requests
I know this has come up before . It would be fantastic if we could use the knock sensor and log knock properly . I see this feature with the dsm guys and it is invaluable .
- Sun Mar 13, 2011 7:57 pm
- Forum: s300 / SManager
- Topic: GM 3 bar MAP sensor
- Replies: 15
- Views: 15897
so the GM 3bar MAP sensor has a scaler of 628 and an offset of 0, and the Motec 3bar MAP sensor has a scaler of 609 and an offset of 2, so am i correct that I need to switch my scaler and offset to the GM settings??? How is this going to effect my current tune? Changing the scaler will have an impa...
- Mon Mar 07, 2011 9:57 am
- Forum: s300 / SManager
- Topic: GM 3 bar MAP sensor
- Replies: 15
- Views: 15897
- Fri Nov 12, 2010 5:38 pm
- Forum: s300 / SManager
- Topic: Smanager wish list
- Replies: 150
- Views: 164723
- Thu Nov 06, 2008 8:38 pm
- Forum: s300 / SManager
- Topic: How record datalog
- Replies: 6
- Views: 4313