Search found 25 matches

by joeb
Sun Oct 02, 2016 4:48 pm
Forum: s300 / SManager
Topic: BBG Settings in Smanager, Boost Control Problems
Replies: 2
Views: 5273

Re: BBG Settings in Smanager, Boost Control Problems

Just a little tip here . Pay close attention to the inlet and outlet of the boost solenoid . I was having issues and finally saw the problem . The boost solenoid was backwards .This made boost control very sensitive for me . I was about to give up on the Hondata boost control . Once i fixed this it ...
by joeb
Tue Jun 07, 2016 6:07 pm
Forum: s300 / SManager
Topic: Boost control issues (searched first!)
Replies: 5
Views: 2172

Re: Boost control issues (searched first!)

Wow , i'm having the same problem . My duty cycles are extremely low as i hit 18 psi with 15 percent duty cycle . I did drop my solenoid frequency down from 78hz to 32hz and it made a very small change . I am going to try and lower the frequency again and see what happens . On my car the quick spool...
by joeb
Thu Nov 14, 2013 6:44 pm
Forum: s300 / SManager
Topic: SManager V2.2.7 (beta)
Replies: 61
Views: 35637

Re: SManager V2.2.7 (beta)

No updates yet ? Wow , its been a while .
by joeb
Tue Oct 22, 2013 6:16 pm
Forum: s300 / SManager
Topic: When the Fan turns off the ECU disconnects.
Replies: 17
Views: 5204

Re: When the Fan turns off the ECU disconnects.

Stock fan swapped in and issue stopped . It only happens with my Spal high cfm unit . I am going to try a capacitor across the fan terminals .
by joeb
Tue Sep 10, 2013 7:36 pm
Forum: s300 / SManager
Topic: WHEN WILL HONDATA COME OUT WITH GREAT KNOCK CONTROL????
Replies: 5
Views: 2092

Re: WHEN WILL HONDATA COME OUT WITH GREAT KNOCK CONTROL????

I have already asked for this . I think the problem is that the architecture of the ecu is old and would be to much trouble to make something work .
by joeb
Fri Aug 09, 2013 8:28 pm
Forum: s300 / SManager
Topic: When the Fan turns off the ECU disconnects.
Replies: 17
Views: 5204

Re: When the Fan turns off the ECU disconnects.

With USB disconnects it is always one of three things: - non resistor spark plugs (check and replace) - laptop chargers than create current loops through the USB cable (run on battery and see if it still occurs) - bad engine / chassis grounds paths The last is the most difficult to track down. Clea...
by joeb
Thu Aug 08, 2013 7:45 pm
Forum: s300 / SManager
Topic: When the Fan turns off the ECU disconnects.
Replies: 17
Views: 5204

Re: When the Fan turns off the ECU disconnects.

Interestingly i have the same problem . I just installed a Spal fan and started having this same issue . When the fan turns on its ok , but as soon as it turns off my laptop freezes . My prior fan never did this . Increased electrical noise must be the issue here . All grounds are clean and in the p...
by joeb
Sat Jun 29, 2013 7:48 pm
Forum: s300 / SManager
Topic: SManager software requests
Replies: 308
Views: 109003

Re: SManager software requests

A timed ignition retard after launch would be fantastic . This is offered by Msd and works well with the hot rod guys .
by joeb
Mon Mar 04, 2013 9:44 am
Forum: s300 / SManager
Topic: closed loop headache....
Replies: 8
Views: 2545

Re: closed loop headache....

In all honesty i just turn off closed loop . I can never get it to work correctly as it is finicky . All the cars i tune with Hondata i leave in open loop and they all run great with excellent fuel economy . Just tune with a wideband in the car and it will be fine . The a/f ratio will change with dr...
by joeb
Sun May 06, 2012 9:50 am
Forum: s300 / SManager
Topic: SManager software requests
Replies: 308
Views: 109003

Re: SManager software requests

I know this has come up before . It would be fantastic if we could use the knock sensor and log knock properly . I see this feature with the dsm guys and it is invaluable .
by joeb
Sun Mar 13, 2011 7:57 pm
Forum: s300 / SManager
Topic: GM 3 bar MAP sensor
Replies: 15
Views: 11754

so the GM 3bar MAP sensor has a scaler of 628 and an offset of 0, and the Motec 3bar MAP sensor has a scaler of 609 and an offset of 2, so am i correct that I need to switch my scaler and offset to the GM settings??? How is this going to effect my current tune? Changing the scaler will have an impa...
by joeb
Mon Mar 07, 2011 9:57 am
Forum: s300 / SManager
Topic: GM 3 bar MAP sensor
Replies: 15
Views: 11754

The motec 3 bar is the same .
by joeb
Fri Nov 12, 2010 5:38 pm
Forum: s300 / SManager
Topic: Smanager wish list
Replies: 150
Views: 47397

It would be very nice if closed loop could be delayed while the car was still cold until a user determined temp was met .
by joeb
Thu Nov 06, 2008 8:38 pm
Forum: s300 / SManager
Topic: How record datalog
Replies: 6
Views: 3217

Hondata wrote:To record a datalog, use F9 or 'record'. You can re-load the datalog and scroll through it, but there is no play back like RomEditor.
Is there a possibility in the future that it will playback like romeditor ?