There are 2 codes. The IAT has been replaced, and the temp reading seems accurate. and not sure how to fix that vtec code P1259.
scott
Search found 8 matches
- Tue Jul 16, 2019 1:40 pm
- Forum: K-Pro Calibrations
- Topic: First start, runs rough and shut off
- Replies: 3
- Views: 1414
- Tue Jul 16, 2019 10:25 am
- Forum: K-Pro Calibrations
- Topic: First start, runs rough and shut off
- Replies: 3
- Views: 1414
First start, runs rough and shut off
I got my JDM k20a euro r to finally start. Using a ktuned harness, and swapped over crank and cam sensors to american K20. Skunk2 intake, b series TB. It fires up, want to rev up to 2500 and then dies down. When it does fire up, it sounds like its mis firing real bad. Tune and log attached. Thanks f...
- Tue Jun 25, 2019 2:22 pm
- Forum: K-Pro / KManager
- Topic: Kpro in Tube frame with JDM motor
- Replies: 9
- Views: 1742
Re: Kpro in Tube frame with JDM motor
ok, thank you for your help. I will see what I can find.
- Tue Jun 25, 2019 1:24 pm
- Forum: K-Pro / KManager
- Topic: Kpro in Tube frame with JDM motor
- Replies: 9
- Views: 1742
Re: Kpro in Tube frame with JDM motor
I just went through and ohm'd every single wire from ecu plug to sensor plug, it is all correct. I would like to try a few things before buying a harness. How can I check the raw data coming in from each sensor? I am trying to figure out this software. I have built over 200 cars from scratch using L...
- Tue Jun 25, 2019 10:06 am
- Forum: K-Pro / KManager
- Topic: Kpro in Tube frame with JDM motor
- Replies: 9
- Views: 1742
Re: Kpro in Tube frame with JDM motor
I took the JDM harness, removed all the pins out of the ECU connectors. I then repined all the sensors to the correct ECU positions as per information on http://www.phearable.net/information/tech-area/02-04-prb-rsx-type-s-ecu-pin-out-diagrams.html I just replaced the crank and exhaust cam sensor tha...
- Mon Jun 24, 2019 7:30 pm
- Forum: K-Pro / KManager
- Topic: Kpro in Tube frame with JDM motor
- Replies: 9
- Views: 1742
Re: Kpro in Tube frame with JDM motor
Latest log and calibration. There were some pins were still off, that are corrected. shouldn't it be reading a CAM angle under cranking? Maybe its a different cam sensor?
- Mon Jun 24, 2019 5:34 pm
- Forum: K-Pro / KManager
- Topic: Kpro in Tube frame with JDM motor
- Replies: 9
- Views: 1742
Re: Kpro in Tube frame with JDM motor
The website says you can under the "alternate ECU" section. And they did mod it already. It's 37820-pnd-a58 and 2063-806057. Thanks
- Mon Jun 24, 2019 2:43 pm
- Forum: K-Pro / KManager
- Topic: Kpro in Tube frame with JDM motor
- Replies: 9
- Views: 1742
Kpro in Tube frame with JDM motor
I am not sure if this is the correct section, I am new to this Hondata world. I have a confusing setup and need some advice on what type of calibration/wiring I should be running. Car is a tube frame race car (Stalker Cars AXR) Engine is k20A2 from JDM Euro R RWD BMW transmission ECU is a 05 Acura R...