scalar for aem 5 bar 1290 off set -645
I cant believe you ask them for the offset and scalar for a popular sensor and they tell you figure it out...typical hondata support.
Search found 26 matches
- Tue Mar 03, 2009 9:35 am
- Forum: s300 / SManager
- Topic: s300 and aem 5 map sensor questions...
- Replies: 5
- Views: 3709
- Tue Mar 03, 2009 9:33 am
- Forum: s300 / SManager
- Topic: aem 5 bar problem
- Replies: 6
- Views: 3266
- Tue Mar 03, 2009 9:21 am
- Forum: s300 / SManager
- Topic: aem 5 bar problem
- Replies: 6
- Views: 3266
I looked at your scalar anf offset equation- for aem 5 bar min voltage and pressure is .5 volts = -1013 mbar max voltage and pressure = 4.5 = 4157.5 mbar range 4.0 volts pressure range = 3144 so the scalar and off set should be 786 and -393 but this gives incorrect pressure readings -voltage so it i...
- Mon Mar 02, 2009 11:25 am
- Forum: s300 / SManager
- Topic: aem 5 bar problem
- Replies: 6
- Views: 3266
aem 5 bar problem
Since I updated my software whenever I downshift or the motor pulls heavy vacuum the ecu throws a code for the map sensor and wont rev. cycle the key and it drives fine until it happens again. aem 5 bar map sensor. was something changed in the update 1.4 because it ran fine before. do you guys have ...
- Mon Mar 02, 2009 11:23 am
- Forum: s300 / SManager
- Topic: s300 and aem 5 map sensor questions...
- Replies: 5
- Views: 3709
- Tue Nov 08, 2005 10:03 pm
- Forum: s300 / SManager
- Topic: SManager V1-1 Beta
- Replies: 84
- Views: 54589
- Mon Oct 17, 2005 3:22 am
- Forum: s300 / SManager
- Topic: SManager V1-1 Beta
- Replies: 84
- Views: 54589
I had the similar result happen on the dyno last night. Newer version of the software, old map... car freaked out and the main relay clicked, etc. The S300 wouldnt take the upload. Tried several times and even tried closing everything and loading it up again, didnt work. Used V1.0.9 on another tune...
- Mon Oct 17, 2005 3:16 am
- Forum: s300 / SManager
- Topic: SManager V1-1 Beta
- Replies: 84
- Views: 54589
Try closing the program and uploading the calibration again. Who did the socketing of your ecu? You are the only person who has experienced this problem, so I suspect it is an isolated issue. I sent it to you guys and no its not socketed wrong.... When you load maps it likes to change them ...almos...
- Thu Oct 13, 2005 11:32 pm
- Forum: s300 / SManager
- Topic: SManager V1-1 Beta
- Replies: 84
- Views: 54589
Update 10/10/2005: ? Added additional tables for water temp correction. Downloaded the new beta.... opened my map...press load and the hondata software freezes and my main relay goes off like a machine gun and all the lights on the dash start pulsing. Disconnect the computer turn the key foward and...
- Wed Oct 12, 2005 5:55 am
- Forum: s300 / SManager
- Topic: SManager V1-1 Beta
- Replies: 84
- Views: 54589
- Thu Oct 06, 2005 1:37 am
- Forum: s300 / SManager
- Topic: SManager V1-1 Beta
- Replies: 84
- Views: 54589
the realtime lamda works again. thanks... I am however still having a problem with the ect compensation and the IAT compensation...both dont seem to do anything at all. no matter what values you enter it does not change the air fuel at all Also switching over to the beta made the entire partial thro...
- Thu Sep 29, 2005 11:57 pm
- Forum: s300 / SManager
- Topic: SManager V1-1 Beta
- Replies: 84
- Views: 54589
- Wed Sep 28, 2005 4:13 pm
- Forum: s300 / SManager
- Topic: This thing has some Major bugs
- Replies: 11
- Views: 8083
- Wed Sep 28, 2005 4:11 pm
- Forum: s300 / SManager
- Topic: HELP ME UNDERSTAND - NOOB!
- Replies: 9
- Views: 6168
Im guessing you are using a factory map sensor... the factory map sensor will read 11 psi so if you run 4 psi it will have different fuel values then at 11 psi. there will be no need to switch fuel maps the map sensor tells the ecu how much boost you are running and will make the appropriate changes...
- Wed Sep 28, 2005 4:07 pm
- Forum: s300 / SManager
- Topic: SManager, the mystery software, will it work today or not.
- Replies: 10
- Views: 6295