Search found 7 matches

by Sneaky_84
Fri May 24, 2019 11:09 am
Forum: S300 Calibrations
Topic: Build B16A Turbo
Replies: 1
Views: 472

Build B16A Turbo

whats up guy i need an basemap to drive my car to the dyno. my built is: -JDM B16A CSS block -JDM B16 head -Supertecht valve train (flat valve) -Skunk2 pro1 cams -Edelbrock intake with 72mm throttlebody -RC1200cc injector -aeromotive regulator -golden eagle fuelrail -Ktuned 4 bar map sensor -Hondata...
by Sneaky_84
Tue May 08, 2018 10:30 am
Forum: S300 Calibrations
Topic: Basemap Needed Build B16A
Replies: 0
Views: 717

Basemap Needed Build B16A

JDM B16A Block & Head Mods: -CSS Block -Arias 10.5:1 81.5mm pistons -Skunk2 Rods -Type-R pump -Skunk2 Valvetrain -Skunk2 LMA -Skunk2 Pro 1 camshafts & Gear -Hondata CPR -Hondata s300v2 (BBG) -Edelbrock VictorX -72mm Throttle body -Speedfactory 3bar map -RC 330cc injectors -Walbro 450LPH intank pump ...
by Sneaky_84
Thu Dec 01, 2016 11:38 am
Forum: S300 Calibrations
Topic: Full build B16A calibration needed
Replies: 0
Views: 809

Full build B16A calibration needed

Hi guys i going to need a calibration for my full build B16a. -B16A block stock sleeve solid deck (CSS) -stock crank -Skunk2 Rods -Arias 81.5mm pistons 10,5:1CR -ARP studs -Full skunk2 valvetrain std size -Skunk2 tuner stage 2 camshaft (not degreed yet) -Edelbrock intake + 70mm TB -Speedfactory map ...
by Sneaky_84
Thu Nov 03, 2016 1:43 pm
Forum: S300 Calibrations
Topic: B16A2 semi allmotor build map needed
Replies: 6
Views: 1873

Re: B16A2 semi allmotor build map needed

thanks, the car is running great now..
by Sneaky_84
Sat Oct 29, 2016 4:05 pm
Forum: S300 Calibrations
Topic: B16A2 semi allmotor build map needed
Replies: 6
Views: 1873

Re: B16A2 semi allmotor build map needed

No i dont have a wideband yet.
And the old owner had the dizzy full advanced.

But tomorow i'm going to the dyno.
by Sneaky_84
Fri Oct 28, 2016 12:30 pm
Forum: S300 Calibrations
Topic: B16A2 semi allmotor build map needed
Replies: 6
Views: 1873

Re: B16A2 semi allmotor build map needed

i install your map, the start up is good. only feel like misfire at idle, maybe because i didn't degree the cams yet.
tomorow i'm goining to let the cams be degreed, will try it again.
by Sneaky_84
Thu Oct 20, 2016 1:47 pm
Forum: S300 Calibrations
Topic: B16A2 semi allmotor build map needed
Replies: 6
Views: 1873

B16A2 semi allmotor build map needed

B16a 2nd gen Engine: -Skunk2 camshaft tuner stage 2 -skunk2 camgear -skunk2 pro intake manifold -skunk2 titanium retainers -skunk2 valve spring -CTR Piston w/ new rings -ACL main&rod bearings -ARP head stud&rod bolts -blueprinted block -OBX throttle body -ITR airbox with air duct to bumper, k&n filt...