Search found 38 matches

by Steeve_Civic
Sun Aug 26, 2018 1:34 am
Forum: s300 / SManager
Topic: Not good gear on Display
Replies: 3
Views: 1113

Re: Not good gear on Display

I changed my gera ratio in Gear comp and it works.
But the module recalculate doesn't work on gear comp, how does it work please?
by Steeve_Civic
Sun Aug 26, 2018 1:33 am
Forum: s300 / SManager
Topic: Strain Gauge From Flatshifter
Replies: 7
Views: 2509

Re: Strain Gauge From Flatshifter

It seems working.
SCS sensor jump to ON when I shift, It switches to ground.
at idle it is a very little cut, Around which duration is good?
by Steeve_Civic
Sun Aug 19, 2018 1:52 pm
Forum: s300 / SManager
Topic: Not good gear on Display
Replies: 3
Views: 1113

Not good gear on Display

Hi,

On hondata S300 display the gear engaged is not the good one.
Do you know how to configure it please ?
Thks
by Steeve_Civic
Tue Aug 14, 2018 3:04 pm
Forum: s300 / SManager
Topic: Strain Gauge From Flatshifter
Replies: 7
Views: 2509

Re: Strain Gauge From Flatshifter

Than you Spunkster
So I need to connect both wires (blue and red) to one anolog wire Input of S300?
Then configure it in Voltage?
Thks
by Steeve_Civic
Tue Aug 14, 2018 12:57 pm
Forum: s300 / SManager
Topic: Strain Gauge From Flatshifter
Replies: 7
Views: 2509

Strain Gauge From Flatshifter

Hi, I have this Flatshifter and would like to ask how to configure it please on S300. https://www.flatshifter.com/flatshifter-strain-gauge-gear-knob/ I have a 2,5V Amplifier module and 4 wires. + Battery - Ground Red wire for Upshift Blue for Downshift Flatshifter answer below: As you have a H patte...
by Steeve_Civic
Mon Jun 30, 2014 2:58 pm
Forum: s300 / SManager
Topic: Old software version?
Replies: 2
Views: 1686

Re: Old software version?

Just changed my laptop and needed to download the new version and need to switch lots of setting.
I saw lots of others options and I m afraid to connect my new laptop to my ECU.
by Steeve_Civic
Mon Jun 30, 2014 12:14 pm
Forum: s300 / SManager
Topic: Old software version?
Replies: 2
Views: 1686

Old software version?

Hi,
Where can I download old software version as 2.0?

Thank you
by Steeve_Civic
Sun Mar 03, 2013 3:19 am
Forum: s300 / SManager
Topic: Burnout Rev Limit Wiring
Replies: 11
Views: 6182

Re: Burnout Rev Limit Wiring

What rpm do you setup your brun out rev?
by Steeve_Civic
Sun Dec 16, 2012 9:38 am
Forum: S300 Calibrations
Topic: Setting up ID1000 in s300
Replies: 5
Views: 5587

Re: Setting up ID1000 in s300

I have a fuel pressure set at 50 PSI with the vacuum line disconnected and 45 PSI when connected.

What are the correct numbers to file in the voltage compensation scale?

Doesn't matter when you boost?
by Steeve_Civic
Sat Dec 01, 2012 1:56 am
Forum: s300 / SManager
Topic: From 750cc to 1000cc
Replies: 6
Views: 2863

Re: From 750cc to 1000cc

Do you know the explications?
by Steeve_Civic
Thu Nov 29, 2012 12:57 pm
Forum: s300 / SManager
Topic: b18c1 turbo calibrations....
Replies: 2
Views: 2057

Re: b18c1 turbo calibrations....

Could you post your map .skl?
by Steeve_Civic
Mon Nov 26, 2012 3:04 pm
Forum: s300 / SManager
Topic: From 750cc to 1000cc
Replies: 6
Views: 2863

Re: From 750cc to 1000cc

ok I will try, but still do not understand.
Could you explain me why it doen't change the fuel table? Fuel table isn't the injector opening time?
by Steeve_Civic
Mon Nov 26, 2012 1:09 pm
Forum: s300 / SManager
Topic: From 750cc to 1000cc
Replies: 6
Views: 2863

Re: From 750cc to 1000cc

OK but that doesn't change the fuel tables numbers ??
by Steeve_Civic
Sun Nov 25, 2012 1:43 pm
Forum: s300 / SManager
Topic: Analog Input for EGT
Replies: 8
Views: 4648

Re: Analog Input for EGT

Thank you, I'm going to check

Best regards,
by Steeve_Civic
Sun Nov 25, 2012 1:10 pm
Forum: s300 / SManager
Topic: Analog Input for EGT
Replies: 8
Views: 4648

Re: Analog Input for EGT

Lol, again thank you.

I will try and let you know.

Is there other good EGT gauges with simple user manual?