Search found 11 matches
- Sun Apr 23, 2017 5:31 am
- Forum: s300 / SManager
- Topic: Car wont idle correctly while moving
- Replies: 11
- Views: 3766
Re: Car wont idle correctly while moving
So idle is adjusted properly. but the s300 still wont change idle and doesnt catch a falling idle when pushing clutch in.
- Tue Feb 21, 2017 5:31 pm
- Forum: s300 / SManager
- Topic: Car wont idle correctly while moving
- Replies: 11
- Views: 3766
Re: Car wont idle correctly while moving
what will this determine? if my IACV is working or not?
- Thu Feb 16, 2017 10:30 pm
- Forum: s300 / SManager
- Topic: Car wont idle correctly while moving
- Replies: 11
- Views: 3766
Re: Car wont idle correctly while moving
my idle adjustment screw is almost closed.
i dont understand why the minum moving idle drops below where its supposed to and never corrects
i didnt decel in gear, i simply put the clutch in then the rpms drop too low and duty cyle goes to 0% from 6.8 seconds on datalog to 7.3
i dont understand why the minum moving idle drops below where its supposed to and never corrects
i didnt decel in gear, i simply put the clutch in then the rpms drop too low and duty cyle goes to 0% from 6.8 seconds on datalog to 7.3
- Wed Feb 15, 2017 10:53 pm
- Forum: s300 / SManager
- Topic: Car wont idle correctly while moving
- Replies: 11
- Views: 3766
Re: Car wont idle correctly while moving
uploaded calibration
also, you can see in the datalog that when i let off throttle to coast, my fuel duty cycle goes to 0% and almost dies.
also, you can see in the datalog that when i let off throttle to coast, my fuel duty cycle goes to 0% and almost dies.
- Sat Feb 11, 2017 3:09 pm
- Forum: s300 / SManager
- Topic: Car wont idle correctly while moving
- Replies: 11
- Views: 3766
Car wont idle correctly while moving
s300v2
b18c turbo
1000cc ID
IACV duty cycle in the middle @ normal
In the IDLE parameters i have my moving minimum idle set to 1500rpm but it does not work.
also if i adjust idle while stationary and upload nothing happens.
ive attached datalog recording
update: attached calibration
b18c turbo
1000cc ID
IACV duty cycle in the middle @ normal
In the IDLE parameters i have my moving minimum idle set to 1500rpm but it does not work.
also if i adjust idle while stationary and upload nothing happens.
ive attached datalog recording
update: attached calibration
- Fri Jan 27, 2017 6:54 pm
- Forum: s300 / SManager
- Topic: ect issue
- Replies: 8
- Views: 2635
Re: ect issue
check thermostat ground?
- Fri Jan 27, 2017 6:37 pm
- Forum: s300 / SManager
- Topic: Security Setting issues
- Replies: 3
- Views: 1460
Security Setting issues
S300V2
I am having issues with using TPS % as security. It used to work fine, now it almost seems intermittent. I use a 80-100% I have re-read tps @ closed and WOT closed is -1.2%. I have tried other security settings and they work (not TPS)
I am having issues with using TPS % as security. It used to work fine, now it almost seems intermittent. I use a 80-100% I have re-read tps @ closed and WOT closed is -1.2%. I have tried other security settings and they work (not TPS)
- Sun Dec 15, 2013 6:47 pm
- Forum: s300 / SManager
- Topic: SManager software requests
- Replies: 336
- Views: 1526241
Re: SManager software requests
sdobart wrote:I'd love to see target-lambda adjustable cell-by-cell, instead of only in 3 groups.
The current setup (low/medium/high load) is difficult when trying to dial in nice fueling transitions between cruising and boost when street tuning using the fuel change table.
Thanks
THIS!!!
- Wed Jan 23, 2013 2:36 am
- Forum: S300 Calibrations
- Topic: cold/warm start up A/F problem
- Replies: 0
- Views: 2087
cold/warm start up A/F problem
2.0l b18c1, rc 440cc, .57 trim t3/4, stock map. I'm having issues with cold/warm start. after its warmed up and my idle is tuned properly. i can shut my car down, then start it back up a few mins later and the a/f ratio will be crazy lean for a couple minutes, even when at normal op temp. using the ...
- Fri Jan 04, 2013 12:45 am
- Forum: s300 / SManager
- Topic: tuning Vss
- Replies: 7
- Views: 4888
Re: tuning Vss
Hondata wrote:No, the dash gets its speed directly from the speed sensor and so cannot be changed by the ECU.
Is there a way to edit this vss % and splice into gauge cluster. i.e. changing type r cluster reading Km/hr to mp/h 1 Kilometer per Hour = 0.62 Mp/Hr.
- Fri Jan 04, 2013 12:00 am
- Forum: s300 / SManager
- Topic: SManager software requests
- Replies: 336
- Views: 1526241
Re: SManager software requests
since a lot of data is collected through data logging and some maths is quite fast programmed, it should be possible to insert some kind of "dyno" to the software, which calculates the power depending on acceleration most of the figures needed are included in the software: gear ratio, rev...