Search found 89 matches
- Fri Apr 18, 2014 7:40 pm
- Forum: s300 / SManager
- Topic: S300 v2 issue
- Replies: 1
- Views: 1080
S300 v2 issue
Got a customer with a brand new s300 v2 and cant install driver/ecu to the laptop. Wont register or anything. Got a red light on the ecu.
- Tue Jun 18, 2013 8:32 am
- Forum: S300 Calibrations
- Topic: Built z6 map needed
- Replies: 5
- Views: 3877
Re: Built z6 map needed
I can make you a full tune. pm me for more info.
- Tue Jun 18, 2013 8:31 am
- Forum: S300 Calibrations
- Topic: D16z6 base map needed plz...
- Replies: 1
- Views: 2085
Re: D16z6 base map needed plz...
use a p28 base map
- Tue Jun 18, 2013 8:29 am
- Forum: S300 Calibrations
- Topic: need map forb18c1 sc61, stock map 1000cc injectors
- Replies: 3
- Views: 1988
Re: need map forb18c1 sc61, stock map 1000cc injectors
you gotta get tuned
- Tue Jun 18, 2013 8:26 am
- Forum: S300 Calibrations
- Topic: B16A2 with 81.5 type R pistons - MAP HELP
- Replies: 5
- Views: 3128
Re: B16A2 with 81.5 type R pistons - MAP HELP
you need to fix your speed sensor. and you running lean at wot. part throttle looks ok.
- Tue Jun 04, 2013 6:26 pm
- Forum: S300 Calibrations
- Topic: B16A2 with 81.5 type R pistons - MAP HELP
- Replies: 5
- Views: 3128
Re: B16A2 with 81.5 type R pistons - MAP HELP
You should be around 10.6:1 with this setup. Use a jdm B16 base map. 50 psi of fuel pressure with factory injectors. It should run and get it to a tuner. then swap the injectors and tune it.
- Mon Jun 03, 2013 8:00 pm
- Forum: S300 Calibrations
- Topic: B16A2 with 81.5 type R pistons - MAP HELP
- Replies: 5
- Views: 3128
Re: B16A2 with 81.5 type R pistons
B16 crank and b16 rods with type r 11.1:1 pistons right. Whats the gasket thikness
- Sun Jun 02, 2013 9:00 pm
- Forum: S300 Calibrations
- Topic: d16z6 n/a fully build with comp cam 59300 76mm p29 pistons.
- Replies: 5
- Views: 3792
Re: d16z6 n/a fully build with comp cam 59300 76mm p29 pisto
That what they say.
- Sun Jun 02, 2013 1:01 am
- Forum: S300 Calibrations
- Topic: B20vtec all motor NEED Base Map!!!
- Replies: 8
- Views: 6443
Re: B20vtec all motor NEED Base Map!!!
If you put some springs and retainers with skunk2 pro 3 cams you should get around 240-245
- Sat Jun 01, 2013 10:47 pm
- Forum: s300 / SManager
- Topic: To HONDATA
- Replies: 1
- Views: 1495
To HONDATA
hello. is there anything wrong with the 2.2.7
- Sat Jun 01, 2013 10:43 pm
- Forum: S300 Calibrations
- Topic: N eed help with this map tuners welcome.
- Replies: 8
- Views: 5780
Re: N eed help with this map tuners welcome.
Last log is blank. Didnt record.
- Sat Jun 01, 2013 10:39 pm
- Forum: S300 Calibrations
- Topic: ignition timing
- Replies: 8
- Views: 5950
Re: ignition timing
FAL is a very good fan it bolts to a civic radiator and it comes with a shroud. Go to Summit racing or Jegs you get a better price there.
- Thu May 30, 2013 10:04 pm
- Forum: S300 Calibrations
- Topic: N eed help with this map tuners welcome.
- Replies: 8
- Views: 5780
Re: N eed help with this map tuners welcome.
I'll check your log tomorrow, im going to bed now.
- Thu May 30, 2013 10:03 pm
- Forum: S300 Calibrations
- Topic: N eed help with this map tuners welcome.
- Replies: 8
- Views: 5780
Re: N eed help with this map tuners welcome.
Use RC 440cc. No you around 12.3:1-12.5:1.
- Thu May 30, 2013 10:00 pm
- Forum: S300 Calibrations
- Topic: ignition timing
- Replies: 8
- Views: 5950
Re: ignition timing
When ecu is in open loop it will run of the map you make. When in closed loop it runs of oxygen sensor or you can get a wideband aem A/F gauge and wire to it. E85 your motor will need about 27% more fuel than 93. So you will need a good pump maybe bosch 44 inline, 6an fuel line bigger injectors atle...